LYNTON

• ISO 20471 Class 1 Superior Waistcoat 
• W11-Y/DS

FEATURES

• Deeper Arm Holes
• Scooped Sides Allowing Pocket Access
• ID PocketMobile Phone Pocket
• 2 Front Bellowed Storage Pockets
• Double Pen Pocket with D Ring

FABRIC

• 100% Knitted Polyester

FASTENER

• Zip

SIZES

• XS-6XL

REFLECTIVE TAPE

• Retromax

ISO 20471 CLASS

• 1

BOX QTY

• 50

LENGTH

• 76-81cm

A double-layered, white polypropylene-filtered washable and reusable face mask that is cool, breathable and comfortable. 

This item is not classified as either PPE or a medical device and is not tested against PPE standards.

TECHNICAL FEATURES

• 2-Layered face mask
• Polypropylene filter outer layer
• Poly-cotton inner layer
• Hypoallergenic materials
• Soft, non-abrasive elastic earloops
• Washable & reusable (up to 50 washes)
• Can be ironed on the inner layer on low heat
• Very breathable, cool and comfortable
• White
• Made in Jamaica

WASHING INSTRUCTIONS

Soak in a small container with warm soapy water (a dishwashing liquid of good quality is sufficient) for 5 to 10 minutes, then rinse thoroughly with cool, clean water to remove any fragrance or soap residue that could aggravate the sinuses. Squeeze out and let dry. 

IMPORTANT:

The outside of this mask will become very dirty as it does its job. Remove the mask by hooking the earloops carefully with your finger and put it directly into your prepared container of washing solution. DO NOT MACHINE WASH. Wash your hands carefully, and then wash your face.

• High-Quality Fingerless Gloves.
• Synthetic silicon-coated palm for extra grip.
• Gel Inserts.
• Comfort Fit.
• Reflective Piping.
• Ideal for use with power tools.
• Sport or gymnasium use.
• Minimal Risk

High quality fingerless gloves for sport or gymnasium use. 

PALM: Leather palm

BACK: Terry towel backing

ADDITIONAL FEATURES: Reflective piping and gel Inserts.

• Extended length for added protection
• Tough exterior to protect against cuts and abrasions
• Comfortable cotton knit lining absorbs moisture

ADDITIONAL FEATURES: Resistant against oils, acids, caustics, alcohols and solvents

• Dielectric insulating gloves made of high-quality natural latex for protection against dangerous voltage. 

MATERIAL: Nitrile

STANDARDS: EN 420, EN 388

CATEGORY: CAT. II

TECHNICAL FEATURES: 

• Made of Aramid fibre 
• Cut-resistant lining reinforced with a steel mesh,
• Resistant to contact with sharp tools and/or oily surfaces

COATING: NITRA-X nitrile

LINING: DuPont™ Kevlar® aramid fibre, steel mesh, polyester

COLOUR: Green-yellow/Black

PROTECTION: Mechanical protection - heavy, protection against cutting - Level 5 (Coupe Test)

GRIP/AREA OF USE: Oily surfaces

APPLICATION: Building and construction, handling of oily metal sheets, mechanical industry, plastic industry, stamping

PALM: Double layer reinforced cow split leather palm 

BACK: White cotton fabric back

CUFF: Durable white cotton fabric back

MATERIAL: Nitrile

STANDARDS: EN 420, EN 388 *, EN 374 *

CATEGORY: CAT. III

TECHNICAL FEATURES: 

• Excellent abrasion resistance: 30,000 cycles **
• Excellent dexterity thanks to a finished coating
• Excellent grip in both oily and damp environments
• Triple nitrile coating that improves glove waterproofness
• Ultra-light glove ensuring exceptional comfort and softness
• Without latex proteins

PALM: NITRA-X nitrile

BACK: Smooth nitrile

LINING: Nylon

CUFF: Pinked edge

COLOUR: Green/Black

LENGTH: 345 mm / 13.6''

THICKNESS: 1.25±0.03 mm (palm) / 0.75±0.03 mm (back)

PROTECTION: Chemical protection, mechanical protection - medium

GRIP/AREA OF USE: Oily surfaces

APPLICATION: Handling chemicals, handling oiled and/or lubricated objects and materials, handling paint, ink, colourings, glues and adhesives, oil and petrol refining, petrochemical industry.

* Following the new EU Regulation 2016/425 and the new standards on protective gloves EN 388:2016, EN ISO 374-1:2016, EN 374-2:2015 and EN 16523-1:2015, COFRA is re-certifying all its protective gloves. For this reason, it is possible that in our stock and on the market there are still gloves with the old standards EN 388:2003, EN 374-1:2003, EN 374-2:2003, EN 374-3:2003. COFRA guarantees that all the productions do not have technical and qualitative differences and are in compliance with the regulations in force.

** Test carried out in COFRA’s laboratories through the testing procedures indicated by EN 388 standard. The results show an abrasion resistance more than three times the highest level indicated by the standard, as proved by the chart here above.

• 18" (46cm) overall length.
• Liquid proof.
• EN388: 2003
• Level 3 - Abrasion Resistance
• Level 1 - Cut Resistance
• Level 1 - Tear Resistance
• Level 1 - Puncture Resistance

• 14" (36cm) overall length
• Liquid proof
• EN388: 2016
• Level 3 - Abrasion Resistance
• Level X - Cut Resistance
• Level 1 - Tear Resistance
• Level 1 - Puncture Resistance
• Level A - ISO 13997 Cut Resistance

MATERIAL: Polyurethane

STANDARDS: EN 420, EN 388 *

CATEGORY: CAT. II

TECHNICAL FEATURES: 

• Made with the innovative NEXTOFIL yarn which gives maximum mechanical performance according to EN 388 standard
• High lightness and breathability
• Lining without glass fibres
• Maximum dexterity and cut resistance
• Washable at 40 °C without altering the cut-resistant and mechanical performances. Test carried out in COFRA’s laboratories **

COATING: Polyurethane

LINING: Braided threads of polyethylene HDPE, NEXTOFIL, polyester, nylon, elastane

COLOUR: Grey/grey

PROTECTION: Protection against cutting - Level D (TDM Test)

GRIP/AREA OF USE: Dry grip

MATERIAL: Nitrile

STANDARDS: EN 420, EN 388

CATEGORY: CAT. II

TECHNICAL FEATURES: 

• Fully coated 
• waterproof
• Knit-wrist
• Very sturdy and highly resistant to mechanical action

COATING: Nitrile

LINING: 100% Jersey cotton

CUFF: 100% Elastic cotton knit wrist

COLOUR: White/navy

PROTECTION: Heavy Mechanical Protection

GRIP/AREA OF USE: Dry grip

APPLICATION: Applications where a very robust glove is required, building and construction, heavy industry, shipping and receiving

MATERIAL: Nitrile

STANDARDS: EN 420, EN 388 *

CATEGORY: CAT. II

TECHNICAL FEATURES: 

• Breathable back
• Knitted wrist,
• Very sturdy and highly resistant to mechanical action

COATING: Nitrile coating up to the knuckles

LINING: 100% Jersey cotton

CUFF: 100% Elastic cotton knit wrist

COLOUR: White/navy

PROTECTION: Heavy Mechanical Protection

GRIP/AREA OF USE: Dry grip

APPLICATION: Applications where a very robust glove is required, building and construction, heavy industry, shipping and receiving

MATERIAL: Nitrile

STANDARDS: EN 420, EN 388 *

CATEGORY: CAT. II

TECHNICAL FEATURES: 

• Robust and water-resistant double-layered nitrile palm 
• Nitrile coating provides excellent protection against oils and grease
• Good cut resistance
• High abrasion resistance
• Oil Protection Technology - Double-layered coating resistant to oils and greases
• Special sand-finished nitrile coating provides superb grip on oily surfaces

COATING: Sand finished nitrile, double-layered, fully coated

LINING: UHMWPE polyethylene, polyester, elastane

COLOUR: White-black/black

PROTECTION: Mechanical protection - heavy, protection against cutting - Level B (TDM Test)

GRIP/AREA OF USE: Oily surfaces

APPLICATION: Building and construction, contact with oils and fats, handling of metal sheets and sharp metal components (even if oily or dirty), maintenance, mechanical and car industry

MATERIAL: Nitrile

STANDARDS: EN 420, EN 388, EN 374, for food contact

CATEGORY: CAT. III

TECHNICAL FEATURES: 

• Extremely durable 
• Perfect fit, ensuring great comfort
• Internally chlorinated and flocked
• Recommended for work requiring excellent mechanical and chemical resistance
• Suitable for food contact
• Does not contain latex proteins
• “Diamond” slip-resistant finish

COATING: Nitrile

INTERNAL FINISH: Flocked

EXTERNAL FINISH: Lozenges (Diamond)

TREATMENT(S): Chlorinated

CUFF: Straight cuff

COLOUR: Green

LENGTH: 330 mm / 13''

THICKNESS: 0,45 mm (18 mil)

PROTECTION: Chemical protection, food, medium mechanical protection

GRIP/AREA OF USE: Humid surfaces

APPLICATION: Agriculture, automotive assembly and component production, automotive painting, chemical industry, cleaning, glue manufacturing, handling of pesticides, horticultural, laboratory, oil refinery, publishing industry, tanning, waste collection

MATERIAL: Nitrile

STANDARDS: EN 420, EN 388 *

CATEGORY: CAT. II

TECHNICAL FEATURES: 

• Made with the innovative NEXTOFIL yarn which gives maximum mechanical performance according to EN 388 standard
• High lightness and breathability,
• Lining without glass fibres
• Maximum dexterity and cut resistance

COATING: Smooth nitrile

LINING: Braided threads of polyethylene HDPE, NEXTOFIL, polyester, nylon, and elastane

COLOUR: Grey/black

PROTECTION: Heavy Mechanical Protection, Cut-Resistant - Level D (TDM Test)

GRIP/AREA OF USE: Dry grip

APPLICATION: Handling of metal sheets and metal components, handling of sharp and blunt tools, mechanical industry, mechanical parts assembly, plastic industry

* Following the new EU Regulation 2016/425 and the new standards on protective gloves EN 388:2016, EN ISO 374-1:2016, EN 374-2:2015 and EN 16523-1:2015, COFRA is re-certifying all its protective gloves. For this reason, it is possible that in our stock and on the market there are still gloves with the old standards EN 388:2003, EN 374-1:2003, EN 374-2:2003, EN 374-3:2003. COFRA guarantees that all the productions do not have technical and qualitative differences and are in compliance with the regulations in force.

• Rubber-dipped PVC chemical gloves
• 18" in length
• One-size
• Reusable, waterproof and durable.
• Protection against oils, grease, domestic use products, in cleaning and agricultural works. 
• Not for use when handling strong solvents or hydrocarbons.
• Anti-slip model with a rough finish for better grip.

• Lightweight polypropylene
• Full zipper front
• Hooded
• Elastic wrist and ankle closures
• ISO 9001 certified

The RP1000 Disposable Comfort Mask provides relief from nuisance levels of non-toxic dust.

It is not for use where concentrations are at or above the Permissible Exposure Limit (PEL). Not NIOSH approved, or suitable for use against toxic or hazardous air contaminants, e.g. paint spray mists, fumes, gases and vapours.

• Extremely lightweight
• Metal nose clip to fit individual facial contours
• Does not impair breathing, voice and vision
• One size
• Packaging: 1 pc

The RP1000 Disposable Comfort Mask provides relief from nuisance levels of non-toxic dust.

It is not for use where concentrations are at or above the Permissible Exposure Limit (PEL). Not NIOSH approved, or suitable for use against toxic or hazardous air contaminants, e.g. paint spray mists, fumes, gases and vapours.

• Extremely lightweight
• Metal nose clip to fit individual facial contours
• Does not impair breathing, voice and vision
• One size
• Packaging: 50/box

DESCRIPTION: Energy absorber integrated into a lanyard including two connectors: an anchorage one and a basic one. The item is designed to reduce the impact force during the fall.

STANDARD: EN 355:2002

LENGTH: 2 m

WEIGHT: 1140 g

LANYARD DIAMETER: ø 11 mm

BASE CONNECTOR: 
       CLOSURE: screw lock,
       MATERIAL: zinc-plated steel,
       MINIMUM RESISTANCE: 23 kN,
       OPENING: 16 mm,
       STANDARD: EN 362

ANCHORAGE CONNECTOR: 
       CLOSURE: automatic lever,
       MATERIAL: chrome-plated steel,
       MINIMUM RESISTANCE: 21 kN,
       OPENING: 53 mm,
       STANDARD: EN 362

TECHNICAL FEATURES:

The connector with ergonomic handle is designed to give unrivalled hold and greater ease of use.

DESCRIPTION: Positioning lanyard with aluminium regulation device. It includes two connectors, a basic one and a terminating one. The item has been studied to allow changing the length quickly, easily and in every moment, also during the use. The protective mantle is an additional protection against abrasions that prolongs the item's lifetime.

STANDARD: EN 358:1999

ADJUSTMENT: sliding device

LENGTH: 2,0 m MAX LENGTH \ 0,6 m MIN LENGTH

WEIGHT: 880 g

LANYARD DIAMETER: ø 12 mm

BASE CONNECTOR: 
       CLOSURE: screw lock,
       MATERIAL: zinc-plated steel,
       MINIMUM RESISTANCE: 23 kN,
       OPENING: 16 mm,
       STANDARD: EN 362

END CONNECTOR: 
       CLOSURE: automatic lever,
       MATERIAL: zinc-plated steel,
       MINIMUM RESISTANCE: 25 kN,
       OPENING: 19 mm,
       STANDARD: EN 362

DESCRIPTION: A basic harness, easy to fit and adjust.

STANDARD: EN 361:2002

ATTACHMENT POINTS: Device with two attachment points for fall arrest, one on the rear and one on the front (obtained by connecting two semi-attachment points A/2). The large, functional dorsal hook is made of forged steel.

ADJUSTMENT: SINGLE - on the lower part of the harness

SIZE / WEIGHT: 
M-2XL - 800 g

DESCRIPTION: A basic harness, easy to fit and adjust.

STANDARD: EN 361:2002

ATTACHMENT POINTS: Device with a single dorsal attachment point for fall arrest. The large, functional dorsal hook is made of forged steel.

ADJUSTMENT: SINGLE - on the lower part of the harness

SIZE / WEIGHT: 
M-2XL - 730 g

DESCRIPTION:

An ergonomic harness designed to follow the natural contours of the body and give greatly improved freedom of movement while working, due to the targeted use of elasticated straps. The dual adjustment gives perfect body grip, while the quick-release buckles make it easier to fit and adjust.

STANDARD: EN 361:2002

ATTACHMENT POINTS: 

Contains two attachment points for fall arrest; one on the rear and one on the front (obtained by connecting two semi-attachment points A/2). The large, functional dorsal hook is made of forged steel.

ADJUSTMENT: DUAL - on the upper and lower parts of the harness.

SIZE / WEIGHT: 
S-2XL - 1140 g
L-3XL - 1180 g

TECHNICAL FEATURES:

Quick-release buckles offer the user fast and easy locking while maintaining high resistance to stresses.

The loop tool carrier offers the user easy and accessible storage of work tools when they are not in use.

DESCRIPTION:

An ergonomic harness with a built-in positioning belt designed to follow the natural contours of the body and give greatly improved freedom of movement while working, due to the targeted use of elasticated straps. The triple adjustment significantly improves body grip, while the quick-release buckles make it easier to fit and adjust. The sturdy positioning belt built into the harness gives the required support with no reduction in comfort.

STANDARD: EN 358:1999, EN 361:2002

ATTACHMENT POINTS: 

Contains four attachment points; one on the rear and one on the front (obtained by connecting two semi-attachment points A/2) for fall arrest, and two on the side for restraint and work positioning. The large, functional dorsal and lateral hooks are made of forged steel.

ADJUSTMENT: TRIPLE - on the upper and lower parts of the harness, and on the central part of the positioning belt.

SIZE / WEIGHT: 
S-2XL - 1740 g
L-3XL - 1820 g

TECHNICAL FEATURES:

 ELASTYX technology successfully introduces the concept of a strong woven elasticated strap, offering unrivalled fit and comfort, as well as exceptional freedom of movement (due to the interweaving of high-tenacity polyester and elastane) while maintaining high resistance to tearing and abrasion.

Quick-release buckles offer the user fast and easy locking while maintaining high resistance to stresses.

The loop tool carrier offers the user easy and accessible storage of work tools when they are not in use.

PERSPIREX technology successfully introduces the concept of perforated sponge material offering the user a high level of breathability with exceptional body grip and guaranteed comfort.

Due to REVERSE-D technology, attachment points can be folded away and closed at any time, and whenever they are not needed. The ability to shut away attachment points prevents the user from remaining accidentally stuck or caught on protrusions and dangerous snags.

MATERIAL: Leather

STANDARDS: EN 420, EN 388 

CATEGORY: CAT. II

TECHNICAL FEATURES:

• Split leather cuffs provide greater resistance to wear and tear and better protection from oils
• The double-layer palm increases the mechanical resistance to abrasion

PALM: High-quality cow split leather - double-layer palm

BACK: High-quality cow split leather

CUFF: Cuffs made of split leather, length of cuffs 70 mm / 2,75’’

COLOUR: Grey

PROTECTION: Mechanical protection - heavy

GRIP/AREA OF USE: Oily surfaces, wet and dry grip

APPLICATION: Agriculture, construction, mechanical industry, soldering

PLUS: High-Quality Cow Split Leather

FEATURES

• ISO 20471 Class 1
• Mesh Ventilated Under-arms & Side Seams
• Segmented Reflective Tape
• Split Hem Design
• 3 Button Placket
• UV Protection to UPF 40+ meeting EN 13758-2

FABRIC

• Coolviz Plus Birdseye Polyester 130gsm

TRIM COLOUR

• Navy Collar

SIZES

• S-6XL

REFLECTIVE TAPE

• Chevron Design Segmented Tape

BOX QTY

• 25

LENGTH

• 73-89cm

FEATURES

• Lycra Storm Cuff
• Hook & Loop-Fastened Mini Cuff-Adjusters
• Concealed Hood in Collar
• Shaped Drop Tail Back
• Two Way Main Zip
• Full-Length Hook & Loop-fastened Storm Flap
• Internal Lower Zipped Pocket
• Hook & Loop-Fastened Front Pockets

FABRIC

• Breathable 150D PU Coated Polyester

COLOUR

• Hi-Vis Yellow and Grey

LINING

• Mesh Lined Body & Sleeves

FASTENER

• Two Way Chunky Zip

SIZES

• S-6XL

REFLECTIVE TAPE

• Retromax

ISO 20471 CLASS

• 3

EN343 RATING

• 3,3

BOX QTY

• 10

LENGTH

• 95-98 cm